normal style=margin-left:31.6pt;tt-indent:-36.15pt;> 【产品描述】
双酚A类不饱和聚酯型鳞片胶泥是由双酚A类不饱和聚酯型类树脂、玻璃鳞片、颜料填料、助剂、溶剂等与固化剂配套组成。
normal style=margin-left:31.5pt;tt-indent:-36.15pt;> 【基本参数】
◆品 牌: 戴森
◆产品名称: 双酚A类不饱和聚酯型鳞片胶泥
◆产品型号: UPGF-90
◆包装规格: 28kg/组
◆组份配比: 25:3
◆漆膜颜色: 灰色
◆施工方式: 喷涂 辊涂 刷涂
【主要特】
◆固化后硬度较高,耐磨好。
◆耐化学能优。
◆优良的机械特、韧及耐疲劳能。
◆耐温好,可耐150℃温。
【产品用途】
适用于电厂脱硫烟道、电镀厂、电池厂、化工厂、化学储区或桶漕、大型水漕、电解池、污、废水处理漕,酸碱中和池以及重防腐要求的作业面和工作场所,如强酸、碱池排污沟槽等作业环境。
鳞片胶泥表观要求及施工能要求:
normal align=center style=tt-align:center;> 检测项目 |
normal align=center style=tt-align:center;> 合格指标 |
normal align=center style=tt-align:center;> 检测项目 |
normal align=center style=tt-align:center;> 合格指标 |
normal align=center style=tt-align:center;> 表观检测 |
normal align=center style=tt-align:center;> 无固态物料聚集、无杂质 |
normal align=center style=tt-align:center;> 堆体积变形 |
normal align=center style=tt-align:center;> 10s内高度下降10mm~20mm |
normal align=center style=tt-align:center;> 匀太 |
normal align=center style=tt-align:center;> 60min内无树脂液分层 |
normal align=center style=tt-align:center;> 流挂 |
normal align=center style=tt-align:center;> 60min内无流淌形变 |
normal align=center style=tt-align:center;> 表干时间 |
normal align=center style=tt-align:center;> 45min±15min |
normal align=center style=tt-align:center;> 鳞片含量 |
normal align=center style=tt-align:center;> ≥30% |
鳞片胶泥物理能:
normal align=center style=tt-align:center;> 项目 |
normal align=center style=tt-align:center;> 聚酯型 |
normal align=center style=tt-align:center;> 抗拉强度,MPa |
normal align=center style=tt-align:center;> ≥23 |
normal align=center style=tt-align:center;> 抗弯强度,MPa |
normal align=center style=tt-align:center;> ≥23 |
normal align=center style=tt-align:center;> 抗压强度,MPa |
normal align=center style=tt-align:center;> ≥70 |
normal align=center style=tt-align:center;> 冲击强度,J/cm² |
normal align=center style=tt-align:center;> ≥0.43 |
normal align=center style=tt-align:center;> 密度,g/cm² |
normal align=center style=tt-align:center;> ≤1.47 |
normal align=center style=tt-align:center;> 树脂含量,% |
normal align=center style=tt-align:center;> 55~65 |
normal align=center style=tt-align:center;> 不可溶分含量,% |
normal align=center style=tt-align:center;> ≥84 |
normal align=center style=tt-align:center;> 空隙率,% |
normal align=center style=tt-align:center;> ≤1.40 |
normal align=center style=tt-align:center;> 巴氏硬度 |
normal align=center style=tt-align:center;> ≥40 |
normal align=center style=tt-align:center;> 线膨胀系数,K-1 |
normal align=center style=tt-align:center;> ≤1.02X10-5 |
【表面处理】
◆钢材表面喷砂处理至Sa2.5级,表面粗糙度30um-75um。
◆电工工具除锈达到St3级。
◆涂有底漆的表面,采用轻扫喷砂或风动(电动)工具进行二次打磨。
【施工条件】
◆底材温度须高于3℃,相对湿度须小于85%。
◆钢板的温度高于温度3℃以上在夏天,阳光暴晒下时,重涂应该在5天内完成,超过5天打磨表面保证附着力
◆被涂底材温度低于5℃时,环氧树脂与固化剂的固化反应停止或变慢,因此建议不能进行施工。
【质量要求】
1、厚度<10μ
2、生产过程中,不得混入杂物,保持产品洁净
3、成品中不得有结块和互粘附等现象
【运输】
本产品可以用任何具有防雨设施的运输设备运输,运输中应轻装轻卸,避免碰撞,并要防止明火。
【储存】
产品应存放在通风阴凉干燥,不得露天存放,应避免潮湿环境,并不得与化学及油污染物质接触。存放处应严禁烟火。
normal align=justify style=tt-align:justify;>